Easy Way To Fix Codec Diagnostics
Speed up your PC in minutes
If you have codec diagnostics on your PC, this user manual can help you.
The diagnostics screen displays an overview of the electromechanical status of each installed module, manufacturing and optional functions.
Only the electric current of each module is displayed. If there are no working (inactive) stations, this indicates the current lifestyle of consumption of inactive decoders over a two-wire line.
As stations move (active), the total current is restructured to represent the power consumption multiplied by the solenoid coils. Current is a popular solution for field wiring conditions.
The station finder will zap the specified station to find a good solenoid valve in the field by listening.
Press the station search function button and select the station number. When the start button is pressed, the controller vibrates the solenoid for up to 30 minutes. A professional can then listen to the underground noise to locate a particular solenoid.
To stop chatting, press our own softkey again or it will stopby itself after 30 minutes.
Wire testing applies a frequency of 70 Hz to all output portions and their two-wire paths, allowing wire tracking and troubleshooting with standard AC current clamps. This is a common diagnostic strategy for traversing ecological soil.
The alternating current drops sharply, especially at two points of the conductive track, if there is a short circuit or short circuit between them.
When the troubleshooting is complete, press the soft key again to turn off the 60Hz wire test mode.
The Diagnostic Codec can be used to identify issues with plug-in connectivity. There are firewood events that go through some kind of chain of communication back and forth.
Then you can add DiagnosticCodec anywhere in the connection chain. Without additional configuration, the Firelog codec is logged in the correlator log file by visiting the INFO level.
MyCodec- # really inspect codec
, diagnostic codec:
When written to the correlator log file, the diagnostic codec replaces all non-printable ASCII characters (with fewer ASCII values compared to 0x20, which contain tabs and line breaks) with an underscore (_).
If the output configuration parameter function can be described as being set to a file, the diagnostic codec will encode output messages mainly for the following reasons:
The following is an example of a specific output message written to a file:
If the mode of any output configuration option is set to Target Recorder, the diagnostic codec formats the most important output messages with an additional prefix:
The following is an example of a fantastic output message that actually gets written to the log file:
03/16/2020 05:45 PM: 14.472 DEBUG  –
To indicate diagNostic codec requires an entry such as “Matches im
Transfer the config file (see next File
Configure plug-in connectivity
If the chain has multiple DiagnosticCodec periods, you can tag it to win each instance and distinguish it from other instances. string is a label used to add specific messages from the current instance. Default: blank.
Specifies the file in which the codec stores its output. The state can be one of the following:
is standard. The codec connects to the log-level correlator log, which is actually triggered with
. is definedlogLevel
– codec writes initiator defined with
logLevel: level every time
Indicates that recorder mode is specifieda. The level can be any wood level correlator. Standard: INFORMATION.
File name: file
Applies when file mode is set. The file is usually either a manual write path or one of the special stdout stderr or. Standard: standard.
is standard. Codec data from the log file for log-level mapping that starts with
– Codec connects to this registry using
. DefinedFile namesShield
can be optional. This is the recognition that is defined in the layout (or omitted entirely if the label is not configured). When a label is usually present, it is enclosed in square brackets.
directionTo the ownerIn the direction of travelMetadata
is the content of some metadata at the point in my chain where the diagnostic codec was placed.
is the specific content of the fieldknowledge of the load at a certain point in the chain, where the human diagnostic codec was placed.
is the date and time the output was recorded.
Log levelStream ID
is the signature of the entire stream, in which experts indicate the recorded message.
is literally the name of the diagnostic codec that is specified in the configuration (usually alt = “*”
Diagnostic CodecChannel name
is the name of the codec chain specified in the configuration.Speed up your PC now with this easy and free download.